China CE Approved Foot Mounted S Series Helical Worm Gearbox aluminum worm gearbox

Product Description

 

Solution Description

 

Item Description

-S Series Helical gearbox
 

 

Item Characteristics
one.Higher modular style.
two.Built-in casting housing,compact dimension,substantial loading help, stable transmitting and minimal noise degree.
3.With the unique equipment geometry, it receives large torque, performance and lengthy life circle.
four.It can attain the direct combination for 2 sets of gearbox.
5.Substantial performance and preserve power.

6.Help save price and minimal upkeep.

 

Product Parameters

one. Technical data

Measurement 38 forty eight fifty eight sixty eight 78 88 ninety eight
Composition BS   BSA   BSF   BSAF   BSAT   BSAZ
Input Power(kW) .18~.seventy five .eighteen~1.five .eighteen~three .25~5.5 .55~7.5 .seventy five~15 1.5~22
Ratio ten.27~165.71 11.forty six~244.74 ten.seventy eight~196.21 11.55~227.20 nine.96~241.09 11.eighty three~223.26 12.75~230.48
Permissible Torque(N.m) ninety one hundred seventy three hundred 520 1270 2280 4000
Bodyweight(kg) 7 10 14 26 50 one hundred one hundred seventy

2: Design choice
 

S series gear units are available in the following designs
S…Y… Foot-mounted parallel shaft helical gear units with solid shaft
SA…Y… Parallel shaft helical gear units with hollow shaft
SAZ…Y… Limited-flange mounted parallel shaft helical gear units with hollow shaft
SF…Y… Flange-mounted parallel shaft helical gear units with solid shaft
SAT…Y… Flange-mounted parallel shaft helical gear units with hollow shaft
S(SF,SA,SAF,SAZ)S… Shaft input parallel shaft helical gear units
S(SF,SA,SAF,SAZ)…R…Y… Combinatorial parallel shaft helical gear units
S(SF,SA,SAF,SAZ)S…R… Shaft input combinatorial parallel shaft helical gear units

 

Resources Info Sheet

Housing materials

Grey Cast iron

Housing hardness

HBS163~255

Gear materials

20CrMnTi alloy metal

Floor hardness of gears

HRC58°~sixty two °

Equipment core hardness

HRC33~48

Input / Output shaft content

40Cr alloy metal

Enter / Output shaft hardness

HRC32~36

Machining precision of gears

correct grinding, 6~5 Quality

Lubricating oil

GB L-CKC220-460, Shell Omala220-460

Heat treatment

tempering, cementiting, quenching, normalizing, etc.

Efficiency

94%~96% (depends on the transmission stage)

Sounds (MAX)

sixty~68dB

Temp. increase (MAX)

40°C

Temp. increase (Oil)(MAX)

50°C

Vibration

≤20µm

Backlash

≤20Arcmin

Brand of bearings

China prime brand name bearing, HRB/LYC/ZWZ/C&U. Or other brands asked for, SKF, FAG, INA, NSK.

Model of oil seal

NAK — ZheJiang or other brands asked for

 

Comprehensive Photos

 

 

Our procedure of creation

 

 

Our solution line

 

 

Firm Profile

 

Organization Profile

Bode  was founded in 2007, which is positioned in HangZhou metropolis, ZHangZhoug province. As 1 expert maker and exporter, we have much more than seventeen years’ expertise in R & D of worm reducer, gear reducer, gearbox , AC motor and relative spare components. We have factory with advanced manufacturing and test products, the powerful development of staff and producing capability supply our customers with large top quality items. Our goods extensively served to different industries of Metallurgy, Chemical substances, lifting, mining, Petroleum, textile, drugs, wood etc. Main markets: China, Africa, Australia, Vietnam, Turkey, Japan, Korea, Philippines… Welcome to ask us any questions, good offer you constantly for you for lengthy term business.

FAQ

Q1: Are you buying and selling business or company?
A: We are factory.

Q2: What types of gearbox can you make for us?
A: Primary products of our business: R, S, K, F sequence helical-tooth reducer, RV sequence worm equipment reducer,H Sequence Parallel Shaft Helical Reduction Gear Box

Q3: Can you make as for each custom made drawing?
A: Indeed, we provide customized provider for clients.

Q4: Can we purchase 1 pc of each merchandise for quality screening?
A: Yes, we are happy to accept demo purchase for top quality testing.

Q5: What data shall we give prior to placing a buy order?
A:  a) Sort of the gearbox, ratio, enter and output kind, enter flange, mounting position, and motor informationetc.
     b) Housing coloration.
     c) Buy amount.
     d) Other unique requirements.

Q6: How lengthy is your shipping and delivery time?
A: Generally it is 5-10 times if the merchandise are in inventory. or it is fifteen-twenty days if the goods are not in stock.

Q7: What is your terms of payment ?
A: thirty% Advance payment by T/T after signing the agreement.70% just before delivery

If you are intrigued in our item, welcome to contact with us.
Our team will do our greatest to satisfy your need to have 🙂 
 

 

US $90-5,500
/ Piece
|
1 Piece

(Min. Order)

###

Application: Motor, Machinery, Marine, Agricultural Machinery
Function: Distribution Power, Change Drive Torque, Speed Changing, Speed Reduction
Layout: Coaxial
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Step: Double-Step

###

Samples:
US$ 90/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:

###

Size 38 48 58 68 78 88 98
Structure BS   BSA   BSF   BSAF   BSAT   BSAZ
Input Power(kW) 0.18~0.75 0.18~1.5 0.18~3 0.25~5.5 0.55~7.5 0.75~15 1.5~22
Ratio 10.27~165.71 11.46~244.74 10.78~196.21 11.55~227.20 9.96~241.09 11.83~223.26 12.75~230.48
Permissible Torque(N.m) 90 170 300 520 1270 2280 4000
Weight(kg) 7 10 14 26 50 100 170

###

S series gear units are available in the following designs
S…Y… Foot-mounted parallel shaft helical gear units with solid shaft
SA…Y… Parallel shaft helical gear units with hollow shaft
SAZ…Y… Short-flange mounted parallel shaft helical gear units with hollow shaft
SF…Y… Flange-mounted parallel shaft helical gear units with solid shaft
SAT…Y… Flange-mounted parallel shaft helical gear units with hollow shaft
S(SF,SA,SAF,SAZ)S… Shaft input parallel shaft helical gear units
S(SF,SA,SAF,SAZ)…R…Y… Combinatorial parallel shaft helical gear units
S(SF,SA,SAF,SAZ)S…R… Shaft input combinatorial parallel shaft helical gear units

###

Housing material
Grey Cast iron
Housing hardness
HBS163~255
Gear material
20CrMnTi alloy steel
Surface hardness of gears
HRC58°~62 °
Gear core hardness
HRC33~48
Input / Output shaft material
40Cr alloy steel
Input / Output shaft hardness
HRC32~36
Machining precision of gears
accurate grinding, 6~5 Grade
Lubricating oil
GB L-CKC220-460, Shell Omala220-460
Heat treatment
tempering, cementiting, quenching, normalizing, etc.
Efficiency
94%~96% (depends on the transmission stage)
Noise (MAX)
60~68dB
Temp. rise (MAX)
40°C
Temp. rise (Oil)(MAX)
50°C
Vibration
≤20µm
Backlash
≤20Arcmin
Brand of bearings
China top brand bearing, HRB/LYC/ZWZ/C&U. Or other brands requested, SKF, FAG, INA, NSK.
Brand of oil seal
NAK — Taiwan or other brands requested
US $90-5,500
/ Piece
|
1 Piece

(Min. Order)

###

Application: Motor, Machinery, Marine, Agricultural Machinery
Function: Distribution Power, Change Drive Torque, Speed Changing, Speed Reduction
Layout: Coaxial
Hardness: Hardened Tooth Surface
Installation: Horizontal Type
Step: Double-Step

###

Samples:
US$ 90/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:

###

Size 38 48 58 68 78 88 98
Structure BS   BSA   BSF   BSAF   BSAT   BSAZ
Input Power(kW) 0.18~0.75 0.18~1.5 0.18~3 0.25~5.5 0.55~7.5 0.75~15 1.5~22
Ratio 10.27~165.71 11.46~244.74 10.78~196.21 11.55~227.20 9.96~241.09 11.83~223.26 12.75~230.48
Permissible Torque(N.m) 90 170 300 520 1270 2280 4000
Weight(kg) 7 10 14 26 50 100 170

###

S series gear units are available in the following designs
S…Y… Foot-mounted parallel shaft helical gear units with solid shaft
SA…Y… Parallel shaft helical gear units with hollow shaft
SAZ…Y… Short-flange mounted parallel shaft helical gear units with hollow shaft
SF…Y… Flange-mounted parallel shaft helical gear units with solid shaft
SAT…Y… Flange-mounted parallel shaft helical gear units with hollow shaft
S(SF,SA,SAF,SAZ)S… Shaft input parallel shaft helical gear units
S(SF,SA,SAF,SAZ)…R…Y… Combinatorial parallel shaft helical gear units
S(SF,SA,SAF,SAZ)S…R… Shaft input combinatorial parallel shaft helical gear units

###

Housing material
Grey Cast iron
Housing hardness
HBS163~255
Gear material
20CrMnTi alloy steel
Surface hardness of gears
HRC58°~62 °
Gear core hardness
HRC33~48
Input / Output shaft material
40Cr alloy steel
Input / Output shaft hardness
HRC32~36
Machining precision of gears
accurate grinding, 6~5 Grade
Lubricating oil
GB L-CKC220-460, Shell Omala220-460
Heat treatment
tempering, cementiting, quenching, normalizing, etc.
Efficiency
94%~96% (depends on the transmission stage)
Noise (MAX)
60~68dB
Temp. rise (MAX)
40°C
Temp. rise (Oil)(MAX)
50°C
Vibration
≤20µm
Backlash
≤20Arcmin
Brand of bearings
China top brand bearing, HRB/LYC/ZWZ/C&U. Or other brands requested, SKF, FAG, INA, NSK.
Brand of oil seal
NAK — Taiwan or other brands requested

What is a worm gear reducer gearbox?

A worm gear reducer gearbox is a mechanical device that uses a worm gear and a worm to reduce the speed of a rotating shaft. The gear reducer gearbox can increase the output torque of the engine according to the gear ratio. This type of gear reducer gearbox is characterized by its flexibility and compact size. It also increases the strength and efficiency of the drive.
worm reducer

Hollow shaft worm gear reducer gearbox

The hollow shaft worm gear reducer gearbox is an additional output shaft connecting various motors and other gearboxes. They can be installed horizontally or vertically. Depending on size and scale, they can be used with gearboxes from 4GN to 5GX.
Worm gear reducer gearboxes are usually used in combination with helical gear reducer gearboxes. The latter is mounted on the input side of the worm gear reducer gearbox and is a great way to reduce the speed of high output motors. The gear reducer gearbox has high efficiency, low speed operation, low noise, low vibration and low energy consumption.
Worm gear reducer gearboxes are made of hard steel or non-ferrous metals, increasing their efficiency. However, gears are not indestructible, and failure to keep running can cause the gear oil to rust or emulsify. This is due to moisture condensation that occurs during the operation and shutdown of the reducer gearbox. The assembly process and quality of the bearing are important factors to prevent condensation.
Hollow shaft worm gear reducer gearboxes can be used in a variety of applications. They are commonly used in machine tools, variable speed drives and automotive applications. However, they are not suitable for continuous operation. If you plan to use a hollow shaft worm gear reducer gearbox, be sure to choose the correct one according to your requirements.

Double throat worm gear

Worm gear reducer gearboxes use a worm gear as the input gear. An electric motor or sprocket drives the worm, which is supported by anti-friction roller bearings. Worm gears are prone to wear due to the high friction in the gear teeth. This leads to corrosion of the confinement surfaces of the gears.
The pitch diameter and working depth of the worm gear are important. The pitch circle diameter is the diameter of the imaginary circle in which the worm and the gear mesh. Working depth is the maximum amount of worm thread that extends into the backlash. Throat diameter is the diameter of the circle at the lowest point of the worm gear face.
When the friction angle between the worm and the gear exceeds the lead angle of the worm, the worm gear is self-locking. This feature is useful for lifting equipment, but may be detrimental to systems that require reverse sensitivity. In these systems, the self-locking ability of the gears is a key limitation.
The double throat worm gear provides the tightest connection between the worm and the gear. The worm gear must be installed correctly to ensure maximum efficiency. One way to install the worm gear assembly is through a keyway. The keyway prevents the shaft from rotating, which is critical for transmitting torque. Then attach the gear to the hub using the set screw.
The axial and circumferential pitch of the worm gear should match the pitch diameter of the larger gear. Single-throat worm gears are single-threaded, and double-throat worm gears are double-throat. A single thread design advances one tooth, while a double thread design advances two teeth. The number of threads should match the number of mating gears.
worm reducer

Self-locking function

One of the most prominent features of a worm reducer gearbox is its self-locking function, which prevents the input and output shafts from being interchanged. The self-locking function is ideal for industrial applications where large gear reduction ratios are required without enlarging the gear box.
The self-locking function of a worm reducer gearbox can be achieved by choosing the right type of worm gear. However, it should be noted that this feature is not available in all types of worm gear reducer gearboxes. Worm gears are self-locking only when a specific speed ratio is reached. When the speed ratio is too small, the self-locking function will not work effectively.
Self-locking status of a worm reducer gearbox is determined by the lead, pressure, and coefficient of friction. In the early twentieth century, cars had a tendency to pull the steering toward the side with a flat tire. A worm drive reduced this tendency by reducing frictional forces and transmitting steering force to the wheel, which aids in steering and reduces wear and tear.
A self-locking worm reducer gearbox is a simple-machine with low mechanical efficiency. It is self-locking when the work at one end is greater than the work at the other. If the mechanical efficiency of a worm reducer gearbox is less than 50%, the friction will result in losses. In addition, the self-locking function is not applicable when the drive is reversed. This characteristic makes self-locking worm gears ideal for hoisting and lowering applications.
Another feature of a worm reducer gearbox is its ability to reduce axially. Worm gears can be double-lead or single-lead, and it is possible to adjust their backlash to compensate for tooth wear.

Heat generated by worm gears

Worm gears generate considerable amounts of heat. It is essential to reduce this heat to improve the performance of the gears. This heat can be mitigated by designing the worms with smoother surfaces. In general, the speed at which worm gears mesh should be in the range of 20 to 24 rms.
There are many approaches for calculating worm gear efficiency. However, no other approach uses an automatic approach to building the thermal network. The other methods either abstractly investigate the gearbox as an isothermal system or build the TNM statically. This paper describes a new method for automatically calculating heat balance and efficiency for worm gears.
Heat generated by worm gears is a significant source of power loss. Worm gears are typically characterized by high sliding speeds in their tooth contacts, which causes high frictional heat and increased thermal stresses. As a result, accurate calculations are necessary to ensure optimal operation. In order to determine the efficiency of a gearbox system, manufacturers often use the simulation program WTplus to calculate heat loss and efficiency. The heat balance calculation is achieved by adding the no-load and load-dependent power losses of the gearbox.
Worm gears require a special type of lubricant. A synthetic oil that is non-magnetic and has a low friction coefficient is used. However, the oil is only one of the options for lubricating worm gears. In order to extend the life of worm gears, you should also consider adding a natural additive to the lubricant.
Worm gears can have a very high reduction ratio. They can achieve massive reductions with little effort, compared to conventional gearsets which require multiple reductions. Worm gears also have fewer moving parts and places for failure than conventional gears. One disadvantage of worm gears is that they are not reversible, which limits their efficiency.
worm reducer

Size of worm gear reducer gearbox

Worm gear reducer gearboxes can be used to decrease the speed of a rotating shaft. They are usually designed with two shafts at right angles. The worm wheel acts as both the pinion and rack. The central cross section forms the boundary between the advancing and receding sides of the worm gear.
The output gear of a worm gear reducer gearbox has a small diameter compared to the input gear. This allows for low-speed operation while producing a high-torque output. This makes worm gear reducer gearboxes great for space-saving applications. They also have low initial costs.
Worm gear reducer gearboxes are one of the most popular types of speed reducer gearboxes. They can be small and powerful and are often used in power transmission systems. These units can be used in elevators, conveyor belts, security gates, and medical equipment. Worm gearing is often found in small and large sized machines.
Worm gears can also be adjusted. A dual-lead worm gear has a different lead on the left and right tooth surfaces. This allows for axial movement of the worm and can also be adjusted to reduce backlash. A backlash adjustment may be necessary as the worm wears down. In some cases, this backlash can be adjusted by adjusting the center distance between the worm gear.
The size of worm gear reducer gearbox depends on its function. For example, if the worm gear is used to reduce the speed of an automobile, it should be a model that can be installed in a small car.

China CE Approved Foot Mounted S Series Helical Worm Gearbox     aluminum worm gearboxChina CE Approved Foot Mounted S Series Helical Worm Gearbox     aluminum worm gearbox
editor by czh 2023-01-25

worm wheels

As one of leading worm wheels manufacturers, suppliers and exporters of products, We offer worm wheels and many other products.

Please contact us for details.

Mail:[email protected]

Manufacturer supplier exporter of worm wheels

Recent Posts